Fiat 500 Replacement Key Fob
It might be time to replace the battery if the 500 remote key fob is not working. If you do replace the battery and it does not work, then the problem could be elsewhere.
At United Locksmith, we specialize in the creation of new keys for old cars. We have all the tools and components needed for this service.
Dead Coin Battery
A dead battery is the primary cause of your Fiat 500 keyfob not locking or unlocking the doors. The battery of the coin cell inside the key fob is likely to drain quickly if you don't use frequently enough. If your remote started to show signs of weakening such as a loss in range and stopped working completely, the battery is probably dead.
Metal clips keep the battery in place in the key fob. If the clips aren't secure, they could cause problems with the contact, which can stop the remote from receiving power. By using a small flathead screwdriver, push the clip that holds the retaining pin open to remove the current battery and replace it with a new one. Be sure to use an identical replacement battery kind of voltage, size, and specification as the original battery.
The key fob might also become corroded or damaged due to exposure to water. Even a short bath in soapy water could harm the electronic chip in. It is best to keep your key fob in a dry location.
fiat 500 spare key may be the cause of your key fob not working properly. Key fobs come with rubber seals that stop them from being damaged by a light rain or splashes of water, but it is vital to keep your keys out of the ocean, pool, and the washing machine!
The key fob is equipped with an electronic chip in it that sends a signal to your car's immobilizer system. The chip is what allows the 500 to start and lock. If it gets wet it will not function.
You can try cleaning the internal electronics of your key fob with isopropyl Alcohol or an electronic cleaner to determine if they are still good. It is best to replace a key fob if it's submerged in salt water instead of trying to fix it yourself.
While a replacement fob could cost a bit of money, it's much less expensive than having to pay for your Fiat 500 to be towed to a dealership and fixed! You can also do it yourself with a few easy steps. Just ensure you have the correct battery type before you attempt to open your key fob. This is a job that's much simpler than it appears, and you can find step-by-step instructions online for virtually any key fob for your car.
Faulty Chip
The chip that is contained in the key fob communicates with the vehicle's immobiliser to ensure that your car is only capable of starting when the correct key is inserted. If the chip is damaged or damaged in any way it will not start.
Damage to the water or a dead phone battery are the most common reasons for an unreliable chip. It is best to hand over the task to a professional locksmith, who can replace the chip quickly and at an affordable cost.
If your key fob does not work after exposure to water that is clean from the tap or rain, remove the battery. Wipe down the electronic component with a paper towel. If the key fob will not work, there is the possibility that it's malfunctioning components and need to be replaced.
Some people will go to their dealer in order to get an entirely new Fiat fob. However, this could be an expensive option. United Locksmith is the best option for you if would like to have your Fiat keyfob repaired at a reasonable cost. We have the equipment and know-how necessary to repair your Fiat key fob in a timely and professional way.
Faulty Receiver Module
Fiat key fobs send an electronic signal to the vehicle that can unlock and close doors (and start the car for vehicles with an automatic transmission) up to 50 feet. However there are some things that can cause the fob to cease working. It could be due to a dead battery or water damage buttons, worn ones, a receiver module issue and signal interference, or an electronic chip malfunctioning.
If the fob was stored in a place that has experienced extreme trauma, like being dropped on a hard floor or being washed in the washing machine or dishwasher, it might not be able to communicate with the car's Body Control Module (BCM). The BCM is a security device that can only accept signals from genuine keys.
If this is the case, you will require replacing your fob. A professional locksmith can take care of every aspect of the key replacement process as well as programming a new one for your 500. They can even provide a clone fob that works exactly like the original (and costs less than the cost).